Slurry Pump Shaft O Ring
Basic Info
Model No.: E109
Product Description
Slurry Pump Shaft O Ring
Introduction:
An O-ring, also known as a packing, or a toric joint, is a mechanical Gasket the shape of a torus; it is a loop of elastomer with a round cross section, designed to be seated in a groove and compressed during assembly between two or more parts, creating a seal at the interface.
The O-ring may be used in static applications or in dynamic applications where there is relative motion between the parts and the O-ring. Dynamic examples include rotating pump shafts and hydraulic cylinder pistons.
O-rings are one of the most common seals used in machine design because they are inexpensive, easy to make, and reliable and have simple mounting requirements. They can seal tens of megapascals (thousands of psi) of pressure.
Material:
O-ring selection is based on chemical compatibility, application temperature, sealing pressure, lubrication requirements, durometer size and cost.
Butadiene rubber
Butyl rubber
Chlorosulfonated polyethylene
Ethylene propylene diene monomer
A brief introduction of the slurry pumps we offer:
Slurry Pump Series:
1. Metal Lined Slurry Pump, SH Type; 2. Rubber Lined Slurry Pump (SHR Type); 3. Hi-Pressure Slurry Pump (SBH Type);
Gravel Pump Series:
1. Hard Metal Sand Pump (SG, SHG Type); 2. WN Dredging Pump (WN Type);
Sump Pump Series:
1. Metal Vertical Slurry Pump (SV Type); 2. Rubber Vertical Slurry Pump (SVR Type);
Local Pump Series:
1. Power Plant Slurry Pump (ZBG Type); 2. Coal Washing Slurry Pump (ZJ Type);
Froth Pump Series
Material Chemical Requirements, Weight % | ||||||||||||||||
Designation | Material Name | C | Mn | Si | Ni | Cr | Mo | Cu | P | V | S | Description | Hardness | |||
A03 | Ni-Hard 1 | 3.0-3.6 | 0.3-0.7 | 0.3-0.5 | 3.3-4.8 | 1.5-2.6 | 0-0.4 | ... | ≤0.3 | ≤0.15 | ||||||
A05 | Ultrachrome | 2.92 | 0.98 | 0.54 | 0.8 | 26~28 | ≤0.8 | ... | 0.062 | .. | 0.051 | 27% Cr Erosion Resistant White Iron | 58-62HRC | |||
A06 | NI-Hard 4 | 3.2 | 0.2 | 1.5 | 4 | 8 | 0.5 | ... | 0.15 | ... | 0.12 | Martensitic White Iron | 62-67HRC | |||
A07 | 15/3 Chrome/Moly Iron | 2.8-3.2 | 0.5-1.2 | 0.8-1.0 | ... | 15-17 | 2.8-3.2 | 0.8-1.2 | ... | ... | ... | Chromium/Molybdenum | ||||
A33 | 1.55 | 1.2 | 1.29 | 1.89 | 36.7 | 1.92 | 1.31 | ... | ... | ... | Corrosion-resistant Chrome | |||||
A49 | Ultrachrome | 1.57 | 0.71 | 1.36 | 2.01 | 28 | 1.96 | 1.32 | 0.038 | ... | 0.027 | 28% Cr, Low C, White Iron | ||||
A61 | Hyperchrome | 4.4-4.6 | 2.0-2.5 | 0.3-0.8 | ... | 30-32 | 2.5-3.0 | ... | ... | 0.2-0.3 | ... | Hypereutectic white iron | ||||
R55 | Standard Natural Rubber | Natural Rubber for erosive applications | 65 Shore | |||||||||||||
U01 | Wear Resistant Polyurethane | Polyurethane Elastomer | 78 Shore | |||||||||||||
Remarks: 1. The above different kinds of material are for for pump wet-end parts, i.e: impeller, volute liner, throatbush, frame plate liner insert, cover plate liner, frame plate liner. 2. We also have C21, C23, and they are for parts like: shaft, shaft sleeve, shaft spacer, gland assembly etc. 3. For shaft sleeves, J04, J05 and J21 are also avaiable. 4. Pump bodies (cover plate and frame plate) and pump base, bearing housing can be made of G01-grey iron, D21-ductile iron. |
Orders of Rubber Seals:
Product Categories : Slurry Pump Parts > Rubber Pump Parts